A good Garmin Striker 4 mount needs to do three things well: hold the screen steady in rough water, keep the controls within easy reach, and let you adjust the viewing angle without wrestling the hardware every time the sun moves.
The Garmin Striker 4, Striker Plus 4, and Striker Vivid 4cv are small enough to fit almost any fishing boat or kayak. Garmin ships a basic tilt and swivel bracket with the fishfinder, but that factory mount is not always the right call for rough water, kayak accessory tracks, multi-boat setups, or installations where the screen needs to sit higher and closer to the operator.
Best Garmin Striker 4 Mounts at a Glance
| Mount | Best For | Mounting Style |
|---|---|---|
| Garmin Tilt/Swivel Mount | Simple factory-style replacement | Drill-down base |
| VAUBORTTI Aluminum Ball Mount | Jon boats, bass boats, small consoles | AMPS plate or track attachment |
| RAM-B-111U Marine Electronics Mount | Modular, multi-device installations | Drill-down ball mount |
| YakAttack Round Base Mount | Fishing kayaks | Accessory track (LockNLoad) |
| Scotty 367 Universal Mount | Boats already running Scotty bases | Scotty post mount |
1. Garmin Tilt/Swivel Mount: Best Factory Replacement
The Garmin tilt and swivel bracket makes the most sense when you need to replace a lost or damaged factory mount, add a second mounting location, or keep the install as simple as possible.
The base screws directly to a flat surface. The fishfinder cradle sits on the adjustable upper section, so the display can tilt and rotate for a better viewing angle. It does not offer the range of motion of a dual-ball mount, but it is compact and purpose-built for the smaller Striker display.
This is also the best option when a tall arm or bulky adapter would eat up space on a narrow console. Removing the display later stays easy: disconnect the power and transducer cables, release the unit from the cradle, and leave the base attached to the boat.
- Factory-style fit for the Striker 4 family
- Compact footprint
- Tilt and swivel adjustment
- Good replacement for a damaged or missing bracket
- Best suited to one permanent mounting location
2. VAUBORTTI Aluminum Ball Mount: Best Overall Value
The VAUBORTTI mount is a practical upgrade for anglers who want more movement than the factory bracket offers, without piecing together a collection of separate mounting components.
It uses two 1-inch ball joints connected by an adjustable center arm. Loosen the center knob and both ends release, letting you raise, lower, rotate, or angle the screen. Tighten the knob and the display locks back into place.
The mount includes round AMPS-pattern plates, so it also works for small fishfinders, chartplotters, and other marine electronics. It ships with a T-bolt attachment compatible with accessory tracks, which gives it more installation flexibility than a basic drill-down bracket.
The aluminum build matters here too. A small fishfinder does not need a heavy-duty arm, but the mounting hardware still has to resist vibration, UV exposure, and repeated adjustment. Aluminum holds up with a more rigid feel than many lightweight plastic alternatives.
- Dual 1-inch ball joints
- Roughly 5.7-inch overall length
- AMPS-pattern mounting plates
- T-bolt attachment for compatible tracks
- Works well on jon boats, bass boats, and compact consoles
3. RAM-B-111U: Best Modular Mounting System
RAM Mounts is the strongest choice when you want to build around a modular system rather than buy hardware that only works in one spot.
The RAM-B-111U uses RAM’s B-size 1-inch ball system, a medium double-socket arm, and a rectangular marine electronics plate. The plate has multiple predrilled mounting positions and is sized for smaller fishfinders and marine electronics, similar to the marine electronics mounts we cover for Lowrance and Humminbird units.
The real attraction is not just the arm, it is the wider RAM ecosystem behind it. That same 1-inch ball system pairs with different drill-down bases, rail bases, track-ball adapters, and arm lengths. You can put compatible bases on two boats and move the display assembly between them instead of buying a full mount for each location.
The rubber-coated ball joints help absorb vibration while allowing broad adjustment, which is useful when the fishfinder needs to be visible from both a seated steering position and a standing fishing position.
The RAM plate is universal rather than molded specifically for the Striker 4. Compare the plate openings against your Garmin bracket before drilling, and use appropriate stainless mounting hardware.
- B-size 1-inch ball system
- Medium double-socket arm
- Rectangular marine electronics plate
- Compatible with numerous RAM bases and adapters
- Easy to expand or reconfigure later
4. YakAttack Round Base Fish Finder Mount: Best for Kayaks
The YakAttack Round Base Fish Finder Mount is the most direct kayak recommendation in this guide because it is built specifically for the three-hole round base used on the Garmin Striker 4.
It connects to YakAttack GearTrac, MightyMount, and many factory-installed kayak accessory tracks. Instead of drilling a fixed bracket into the hull, you slide the mount into the track and position it wherever the screen is easiest to see and reach. For the full rundown on how these tracks work together, see our YakAttack mounting system guide.
YakAttack’s LockNLoad system is more secure than a basic friction-only ball mount. It locks into set positions while still allowing the screen to be adjusted or removed when needed, which helps prevent the fishfinder from slowly rotating out of position as a kayak moves through waves or gets bumped by fishing gear.
Quick removal matters on a kayak. A fishfinder left standing above the deck can catch on garage doors, vehicle racks, and storage covers. The YakAttack assembly comes off the track before the kayak gets loaded onto a vehicle.
- Designed for the Garmin Striker 4 round base
- LockNLoad adjustment and removal system
- Fits GearTrac, MightyMount, and many factory tracks
- No permanent drill-down base on compatible kayaks
- Built for fast removal during transport
5. Scotty 367 Universal Fish Finder Mount: Best for Scotty Bases
The Scotty 367 makes the most sense for boat and kayak owners who already have Scotty bases installed for rod holders, camera mounts, or other fishing accessories.
Rather than introducing another mounting ecosystem, the fishfinder attaches through the same style of Scotty post base. The universal top plate is built for fishfinders up to roughly 9 inches, so the lightweight Striker 4 sits well within its intended device range.
The mount rotates a full 360 degrees, making it easy to turn the display toward the operator or away from the cockpit when getting in and out of the boat. Its heavy-duty nylon construction keeps weight down and avoids the corrosion concerns that come with untreated metal hardware.
It is not as compact as the Garmin factory bracket and does not offer the same fluid positioning as a dual-ball aluminum mount. Its value comes from the removable post design and compatibility with an established line of Scotty bases, the same ones covered in our guide to kayak track mount systems.
- Universal plate for fishfinders up to about 9 inches
- 360-degree rotation
- Heavy-duty nylon construction
- Works with compatible Scotty mounting bases
- Good choice for existing Scotty installations
Which Garmin Striker 4 Mount Should You Buy?
| Your Situation | Best Choice | Why |
|---|---|---|
| You only need a replacement bracket | Garmin Tilt/Swivel Mount | Simple factory-style replacement |
| You want the best overall adjustment | VAUBORTTI Aluminum Ball Mount | Dual-ball movement and AMPS plates |
| You want a reusable mounting ecosystem | RAM-B-111U | Many compatible bases, arms, and adapters |
| You fish from a track-equipped kayak | YakAttack Round Base Mount | Secure track installation and fast removal |
| Your boat already uses Scotty bases | Scotty 367 | Keeps everything in the same accessory system |
Where to Mount a Garmin Striker 4
Bass Boat Console
Place the display where it can be read without leaning forward or looking sharply away from the water. An adjustable ball mount is useful here because the screen can turn toward the driver’s seat while underway and reposition when fishing.
Jon Boat Bench or Side Rail
Space is usually the biggest constraint in a jon boat. Avoid mounting the fishfinder where it blocks the center walkway, interferes with a bench cushion, or gets hit while rods are being moved. A compact ball mount can raise the screen above the bench while keeping the base close to the side of the boat.
Fishing Kayak Track
Keep the screen within arm’s reach but far enough forward that it does not interfere with paddling, pedal-drive movement, or rod handling. A track mount lets you test several positions before settling on the final spot, and pairs well with a properly positioned transducer mount for clean sonar readings.
Pontoon Helm
A position beside the steering wheel usually gives the easiest viewing angle. Make sure the display and arm do not interfere with switches, gauges, the throttle lever, or access panels beneath the console.
Portable and Ice-Fishing Setup
A portable install can place the Striker 4, battery, and transducer cable on a removable case or board. In this situation the factory mount is often sufficient, since the entire platform can be repositioned rather than adjusting the screen through a long arm.
Installation Tips
- Check underneath the mounting surface. Confirm screws will not hit wiring, steering components, hoses, or the hull.
- Use marine-grade hardware. Stainless steel fasteners hold up better in damp and saltwater environments.
- Seal drilled openings. Use an appropriate marine sealant around holes in exposed decks and consoles.
- Leave cable slack. The display needs enough power and transducer cable slack to move through its full adjustment range without pulling on the connectors.
- Avoid storage lids. Confirm compartments can still open fully once the arm and display are installed.
- Check the sun angle. Mounting directly in front of a reflective windshield can make the screen harder to read.
- Do not overtighten plastic parts. Tight enough to prevent movement is sufficient. Excess force can crack plastic brackets or mounting tabs.
Common Mounting Mistakes
Mounting the Display Too Low
A screen mounted almost flush with a bench or console may look clean, but it forces you to look down repeatedly. Raising the fishfinder a few inches often makes it easier to monitor sonar while keeping your attention on the water.
Choosing an Arm That Is Too Long
A long arm increases leverage on the base. The Striker 4 is lightweight, so an oversized arm is rarely necessary. Use the shortest arm that still puts the display where you can comfortably reach it.
Ignoring Cable Movement
The screen may rotate perfectly while the power cable becomes tight behind it. Test the mount through its complete range of motion before tying down the cables.
Blocking Other Equipment
Check the movement of the throttle, steering wheel, trolling motor controls, rod holders, and storage lids. A good fishfinder location should not create a new obstruction.
Frequently Asked Questions
Does the Garmin Striker 4 come with a mount?
Yes. New Striker 4 packages normally include Garmin’s basic tilt and swivel bracket. An aftermarket mount only becomes necessary when you want more adjustment, a kayak-track installation, a second mounting location, or replacement hardware.
Do the Striker 4 and Striker 4cv use the same mounting style?
The compact Striker 4-series models use closely related cradle and mounting hardware. Always compare the exact model number and bracket description before ordering a replacement, particularly with third-party hardware.
Can the Garmin Striker 4 use a RAM mount?
Yes. A universal RAM marine electronics plate can support the Garmin bracket when the mounting holes line up correctly and are secured with suitable hardware. RAM also offers a large selection of compatible bases and arms.
What is the best Garmin Striker 4 kayak mount?
The YakAttack Round Base Fish Finder Mount is the most direct recommendation for kayaks with compatible accessory tracks. It is built specifically around the three-hole round mounting pattern used by the Striker 4.
Can I move one Striker 4 between two boats?
Yes. Install compatible bases or brackets on both boats, then move the display and the removable portion of the mount. RAM-style ball systems work particularly well for this kind of setup.
Is a 1-inch ball strong enough for the Striker 4?
The Striker 4 is a small, lightweight display, so a quality 1-inch ball mount is generally appropriate. Larger chartplotters and heavier electronics may need a 1.5-inch or larger ball system.
Can the mount attach to a kayak without drilling?
Yes, when the kayak has a compatible accessory track. Track-mounted YakAttack and T-bolt systems install without drilling a permanent base into the kayak.
Should I remove the fishfinder when transporting the boat?
Removing the display protects it from road debris, theft, and unnecessary vibration. Kayak-mounted electronics should almost always come off before the kayak is loaded onto a roof rack or trailer.
Final Recommendation
The Garmin factory bracket is still a good answer for a basic installation. It is compact, familiar, and simpler than replacing the entire mounting system.
For most bass boats, jon boats, and small consoles, the VAUBORTTI aluminum ball mount is the more useful upgrade. Its dual-ball design provides a much broader viewing range, and the AMPS plates plus included track attachment open up several installation options.
Choose the RAM-B-111U when modularity matters more than keeping things simple. It is the better long-term system for owners who plan to add bases, move equipment between boats, or change electronics down the line.
For a track-equipped fishing kayak, the YakAttack Round Base Fish Finder Mount is the clear winner. It is purpose-built for the Striker 4 mounting pattern and comes off quickly when the kayak needs to be transported or stored.
The right Garmin Striker 4 mount does not need to be complicated. Match the mounting style to your boat, use the shortest practical arm, and test the viewing position before drilling any holes.
