Finding the right Mercedes-Benz CLA phone mount depends almost entirely on which generation you own. The CLA changed its dashboard layout twice, first moving from a small 7 or 8 inch touchscreen to a 10.25 inch display around 2020, and the vent and bezel shapes changed along with it. A mount built for the newer screen will not clip onto the older one, and vice versa, and a listing that simply says “fits CLA” without a year range is not worth trusting on its own. This guide covers the 2015 to 2025 CLA specifically.
Mercedes-Benz introduced an all-new CLA for 2026 with a completely redesigned dash, a different screen setup, and vent styling unlike either older generation, so none of the mounts below are confirmed for that car. We will cover the redesigned CLA separately once confirmed-fit mounts for its dash exist. Below are the mounts we have confirmed for the 2015-2019 and 2020-2025 generations, along with a universal air vent option that works across both.
The CLA’s compact cabin also means placement matters more than it does in larger Mercedes-Benz models. The center stack sits close to the driver, so a mount that adds too much bulk near the screen can end up in the way of the climate controls or the volume dial. Every pick below was chosen with that tight layout in mind, favoring mounts that clamp onto existing hardware rather than ones that need extra dash space.
Comparison Table: Mercedes-Benz CLA Phone Mounts
| Mount | Best For | Years / Trim |
|---|---|---|
| FETUSI 10.25″ Screen Mount | MagSafe owners with the big center screen | CLA 2020-2024, 10.25″ screen trim (CLA250/CLA35/CLA45) |
| Batdiary Aluminum Magnetic Mount | Drivers who want an OEM-look vent mount instead of a screen clip | CLA 2020-2026 |
| TUYICN 8″ Screen Clip Mount | Older CLA owners with the smaller touchscreen | CLA 2015-2019, 8″ screen |
| soukeo Adjustable Screen Clip Mount | Drivers who want height adjustment without blocking the vent | CLA 2015-2019 |
| andobil Round Air Vent Mount | A universal fallback that skips the screen entirely | Any CLA year, round vents only |
Current-Generation CLA (2020-2025): Screen and Vent Mounts
The second-generation CLA (C118) introduced a floating 10.25 inch touchscreen mounted high on the dash, close to the driver’s line of sight. That position makes a screen-edge clip mount the natural choice, since it puts the phone at the same height without adding a second stalk to the dashboard. This generation covers the CLA250, AMG CLA35, and AMG CLA45 and CLA45 S, all of which share the same dash and screen setup. If you know your CLA falls into this generation, start here. For general MagSafe background beyond this one vehicle, our MagSafe car mount guide covers magnet strength and mounting angles in more depth.
FETUSI 10.25″ Screen Mount (MagSafe)
This mount clamps onto the bezel surrounding the CLA’s 10.25 inch center display rather than the glass itself, using spring-loaded arms that grip the frame edge. It carries a built-in MagSafe-strength magnet ring, so an iPhone with a MagSafe case snaps on directly, and Android phones work with the included metal plate. Because it attaches to the housing and not the screen surface, there is no adhesive and no risk of scratching the display.
Batdiary Aluminum Magnetic Mount
Not every CLA owner wants a mount hanging off the touchscreen bezel. The Batdiary mount takes a different approach, using a molded aluminum base built to match the CLA’s factory trim and air vent opening, with silicone tips that keep the fit snug without marking the plastic. It shares its bracket family with Mercedes-Benz GLA, GLB, GLE, and GLS models, and it holds the phone with embedded magnets rather than a mechanical clamp. This is the pick for drivers who prefer the phone lower and closer to the vent rather than up near the screen.
Older CLA (2015-2019): Screen Clip Mounts
The first-generation CLA (C117) ran a smaller 7 or 8 inch touchscreen set lower and closer to the center of the dash. This generation covers the CLA250 and CLA45 AMG. Mounts built for the current CLA’s larger display will not clip onto this older bezel, so check your screen size before ordering. Both mounts below are designed specifically around the smaller frame.
TUYICN 8″ Screen Clip Mount
Built for the 7 to 8 inch screen used on the 2015 to 2019 CLA, this mount uses a spring clip that grips the bezel edge without tools or adhesive. The cradle rotates a full 360 degrees, so switching between portrait navigation and landscape video is a one-hand motion. It is made from ABS plastic rather than metal, which keeps it light but also means it is not the mount to reach for if you want a premium look to match the CLA’s interior.
soukeo Adjustable Screen Clip Mount
The soukeo mount fits the same 7 to 8 inch first-generation screen, but adds a height-adjustable arm so the phone can sit slightly higher or lower depending on where you want it in your sightline. The clip is shaped to sit around the bezel without extending into the air vent below it, which some competing clips in this size range tend to block. Reviewers note the silicone and ABS build runs quiet on rough roads, without the rattle some cheaper clip mounts develop after a few months.
Universal Fallback: Round Air Vent Mount
If you are not sure which generation your CLA falls into, if the dash trim has been swapped, or if you simply want a mount that skips the screen bezel altogether, an air vent clip is the safer universal choice. The CLA’s air vents are round, not the horizontal blade or mesh style found in some other vehicles, so a vent mount built specifically for round vents is required here.
andobil Round Air Vent Mount
This clip is built around round vent openings specifically, which makes it a fit for both CLA generations as well as other Mercedes-Benz models that share the same round vent design. The spring mechanism and silicone pads keep it seated against vibration, and the ball joint rotates a full 360 degrees for either portrait or landscape use. It supports phones from 4.7 to 7.2 inches, with or without a case.
How to Choose the Right Mercedes-Benz CLA Phone Mount
Start by identifying which generation you have. If your CLA has a floating 10.25 inch touchscreen mounted high on the dash, you have the 2020 to 2025 model and should look at the FETUSI or Batdiary mounts above. If your screen is smaller, roughly 7 to 8 inches and set lower on the center stack, you have the 2015 to 2019 model, and the TUYICN or soukeo mounts are built for that bezel.
From there, decide between a screen clip and a vent clip. A screen clip puts the phone at eye level next to the display, which is useful for navigation, but it does add weight to the bezel edge over time. A vent clip sits lower and never touches the screen, at the cost of a slightly less convenient viewing angle. Either style works fine for daily use; the choice comes down to where you want the phone positioned and whether you would rather avoid contact with the display trim entirely.
Finally, check magnet compatibility if you are running an iPhone with MagSafe or a magnetic ring case. The FETUSI and Batdiary mounts both support magnetic attachment, while the two older-generation clip mounts use a mechanical cradle instead. Mechanical cradles hold a slightly wider range of phone sizes without needing an added metal plate, which matters if you swap phones between family members or upgrade devices mid-lease. If you drive a different Mercedes-Benz model, our GLS phone mount guide and E-Class phone mount guide cover similar dash layouts.
One more thing worth checking before you order: trim level can occasionally change screen size within the same model year, particularly on base trims that shipped with the smaller display after the rest of the lineup moved to 10.25 inches. If you are not sure which screen your CLA has, measure the display diagonally rather than relying on the model year alone.
FAQ
Will a mount made for the new CLA fit my older 2017 CLA?
No. The touchscreen size and bezel shape changed between generations, and a mount clamped for the larger 10.25 inch display will not grip the smaller 7 to 8 inch screen used through 2019.
Do these mounts block the CLA’s air vents?
The screen clip mounts do not touch the vents at all, since they attach to the display bezel. The andobil vent mount does sit inside the vent opening but is designed to leave airflow largely unobstructed.
Are any of these mounts specific to the CLA35 or CLA45 AMG?
No. The AMG CLA35 and CLA45 share the same dash and screen layout as the standard CLA250 for a given model year, so the mounts above fit all three trims.
What if my phone is not MagSafe compatible?
The FETUSI and Batdiary mounts both include a thin metal ring you can attach to the back of your phone or case to enable magnetic mounting on non-MagSafe devices.
Can I use a windshield or dashboard suction mount in the CLA instead?
Yes, though the CLA’s low, raked windshield puts a suction mount further from the driver’s eyeline than a screen or vent clip. If you would rather explore that route, our suction cup mount guide covers windshield and dash options in more detail.
Do I need to remove any trim to install these mounts?
No. Every mount on this page is a clip-on or magnetic design. None require drilling, adhesive on the dash, or removal of factory trim pieces, so the CLA’s original panels stay untouched if you ever want to sell the mount separately or move it to another car.
