Finding the right Kia EV9 phone mount starts with a decision most owners do not think about until they are already frustrated: do you want a mount built specifically around the EV9’s sweeping 12.3-inch display, or a universal mount that lives on the windshield or in the cup holder instead. The EV9’s dashboard is wide and mostly flat, with the panoramic display sitting high and close to the driver, which limits where a traditional clamp or suction mount can actually go.
The EV9’s three row layout also means the center stack has to do more work than in a typical two row SUV, with climate controls, drive mode settings, and rear seat functions all routed through the same 12.3-inch touchscreen. That leaves very little dash real estate that isn’t already earning its keep, which is exactly why a mount tied to the screen bezel or a suction base on the windshield tends to work better here than a generic vent clip.
Below we cover two mounts engineered specifically for the EV9’s screen bezel, plus three universal options for owners who would rather keep their phone off the display entirely.
| Mount | Best For | Years/Trim |
|---|---|---|
| FICS Custom EV9 Phone Holder | A factory-integrated look with no adhesive or tools | 2024 and newer, 12.3″ display |
| MaserWeller EV9 MagSafe Screen Clip Mount | MagSafe iPhone owners who want a magnetic clip mount | 2024 to 2026, 12.3″ display only |
| VICSEED MagSafe Vacuum Suction Mount | Strong windshield or dash suction with a folding arm | All years, any trim |
| WeatherTech CupFone | Owners who would rather use a cup holder than the dash | All years, any trim |
| elitehood MagSafe Vacuum Suction Mount | A budget-friendly windshield suction option | All years, any trim |
FICS Custom EV9 Phone Holder (Side Screen Mount)
FICS is a Korea based manufacturer that builds nothing but vehicle-specific phone mounts, and this Kia EV9 phone mount is reverse engineered from a 3D scan of the EV9’s dashboard. It clips onto the edge of the 12.3-inch panoramic display with a hook based design, so there is no adhesive, no tape, and no tools involved in the install. The lower edge of the bracket seats first, then the top piece rotates into place along the bezel.
Because the mount attaches to the display frame rather than the dash itself, it sits close to eye level and does not compete for space with the vents or climate controls. The tradeoff is that it is not a magnetic head, so you will need a case with a clamp friendly profile or a slim case that fits the cradle without adding too much bulk.
FICS builds these brackets out of PC plus glass fiber, a combination chosen specifically for heat resistance, which matters in a cabin that sits under a large windshield through direct sun for hours at a time. Because the mount is purpose built rather than adjustable, there is no wobble or flex once it is seated, and it can be removed and reinstalled without leaving any residue or marks on the display trim.
MaserWeller EV9 12.3″ MagSafe Screen Clip Mount
The MaserWeller mount takes a different approach to the same problem. Instead of a hook and bracket, it uses a clip that fits the exact contour of the EV9’s 12.3-inch screen housing, built from a 3D scan of the interior. A black aluminum alloy head holds a ring of magnets rated for MagSafe strength, so the phone attaches and releases with a single motion rather than sliding into cradle arms.
This is a single model fit mount, meaning it is built for the 2024 through 2026 EV9 with the 12.3-inch display and will not work on earlier trims with a smaller screen. The install is non-destructive and can be removed at any time without leaving marks on the dash or display bezel. For anyone who already carries a MagSafe case, this is the fastest mount to use one-handed while backing out of a driveway or grabbing the phone at a red light.
VICSEED MagSafe Vacuum Suction Mount
If you would rather keep the phone off the display entirely, a windshield or dash suction mount is the more traditional route. The VICSEED mount uses a vacuum locked base rated for a strong hold on glass and most dash surfaces, paired with a 360 degree rotating head and a folding zinc alloy arm that adjusts through a wide range of angles. It works with MagSafe cases directly and with standard cases when paired with a metal ring, and the enclosed magnetic field will not interfere with wireless signal or NFC payments.
Because it is not tied to the EV9’s screen shape, this mount also travels well if you switch vehicles later. The folding arm collapses down when not in use, which keeps the base compact for owners who do not want a permanent fixture on the dash.
Several states restrict or prohibit mounting devices directly on the windshield. Check your local regulations before choosing a windshield location, and use the dash placement instead if your state restricts it.
WeatherTech CupFone (Cup Holder Mount)
The EV9’s front cup holders are deep and well spaced, which makes a cup holder mount a genuinely good option rather than a compromise. The WeatherTech CupFone drops into the cup holder and holds the phone at a low, stable position within easy reach of the driver. It does not touch the dash, the screen, or the vents, so there is nothing to remove or clean up if you decide to stop using it.
The tradeoff is the obvious one: you give up a cup holder. For EV9 owners with two front cup holders and a center console storage area, that is an easy trade to make, especially for anyone who does not want any hardware attached to the dash or display.
elitehood MagSafe Vacuum Suction Mount
The elitehood mount covers the same windshield and dash placement as the VICSEED option above, at a lower price point, with a vacuum locked suction base and a MagSafe compatible magnetic head. It is a solid choice for owners who want a simple magnetic mount without paying for the extra features found on premium suction mounts, such as an extended folding arm or a reinforced locking lever.
As with any suction mount, surface preparation matters more than the mount itself. Clean the windshield or dash thoroughly with glass cleaner before applying the suction cup, and let it sit for a few minutes before loading the phone for the first time.
Custom Screen Mount or Universal Mount: Which Should You Pick?
The custom screen mounts from FICS and MaserWeller are the better pick if you want your phone to sit close to eye level without adding anything to the dash surface itself. Both are locked to the 12.3-inch display trim, so confirm your EV9 has that screen configuration before ordering either one.
The universal options make more sense if you want a mounting location that has nothing to do with the screen at all, whether that is because you are not comfortable clipping anything to the display bezel or because you simply prefer a lower mounting position. The WeatherTech CupFone is the least intrusive of the three, while the VICSEED and elitehood suction mounts give you more flexibility to position the phone higher and closer to your line of sight.
Families running the third row regularly should also weigh how often the front passenger needs the cup holder or the dash clear for other gear. A screen edge mount keeps both cup holders and the entire dash surface free, which is worth factoring in if the EV9 doubles as a road trip vehicle with rear seat passengers who need snacks and drinks within reach up front.
Frequently Asked Questions
Will the FICS and MaserWeller mounts fit every Kia EV9 trim?
Both are built around the 12.3-inch panoramic display that comes standard across the EV9 lineup. Confirm your trim has this display before ordering, since a mismatched screen size will keep the bracket from seating correctly.
Do the suction mounts work on the EV9’s dashboard, or only the windshield?
Both the VICSEED and elitehood mounts work on flat dash surfaces as well as the windshield. The dash gives a lower profile and keeps the phone out of your direct line of sight through the glass.
Is a cup holder mount stable enough for highway driving?
Yes. The WeatherTech CupFone uses a spring loaded base designed to stay snug in a range of cup holder sizes, and the EV9’s front cup holders are deep enough to hold it securely.
Can I use a MagSafe case with a non-MagSafe mount from this list?
The FICS mount uses a clamp style cradle rather than magnets, so it works with any case, MagSafe or not. The MaserWeller, VICSEED, and elitehood mounts are all built around MagSafe strength magnets and work best with a genuine MagSafe case or a magnetic ring adapter.
Will a screen edge mount block Kia Connect or the digital gauge cluster?
No. Both the FICS and MaserWeller mounts attach to the outer edge of the infotainment display and are positioned so the phone sits beside the screen rather than over it, leaving the digital gauge cluster and Kia Connect controls fully visible and accessible.
Related Reading
If you are cross-shopping the EV6, our Kia EV6 phone mount guide covers the same screen edge and universal mount categories for that model. For a deeper look at magnetic mounting in general, see our MagSafe car mount buyer’s guide, and for windshield and dash suction options across other vehicles, check our suction cup phone mount roundup.
